MediSure BLOOD GLUCOSE MONITORING SYSTEM Guide de l'utilisateur

INTRODUCTIONPRINCIPLEINDICATIONS FOR USEINTRODUCTIONWe would like to thank you for making a smart decision! The Blood Glucose Monitoring System is des

810) Press the“＞” button or “＜” button until the correct hour is displayed.11) Press the “S” button. The minutes flash.12) Press the“＞”

92.3 Alarm setting1) Press the “＜” button（Left arrow button）≧3 seconds on the front of the meter. MLS2)2) You will hear a beep, and the meter

To quickly adjust a certain number, keep pressing the “＞” or “＜”button until the one you want appears.At any steps if you want to

11MLSC4)Medi+SureTM5) When the control bottle symbol flashes on the meter, it means that you can start testing. You have 3 minutes to apply t

12(1)(2)(3)(4)(5)(6)(8)(9)(10)1) Wash your hands with soap and warm water and dry them thoroughly. Remove the lancing devices cover.2) Place a

132.6 Testing Your Blood Glucose1) Take one test strip out of the test strip vial. Replace the vial cap immediately and close it tightly.

146) Pick up the meter and use the most comfortable way to touch the blood drop to the edge of the application point of the test strip. The

15If you get a high or low reading and you do not feel ill ;• Repeat your measurement.• Make sure your readings are in mg/dL.• Test your meter with

STEP1: CLEAN BEFORE DISINFECTING1.Dispense CaviWipes towelette.2.Clean surface of your device including meter and lacing device (not shown) with tow

＊Why is the disinfection of this device required?The FDA in the USA has issued a new regulation regardingpublic health notifications highlighting the

IMPORTANT SAFETY INSTRUCITONS: Reference:1. “FDA Public Health Notification: Use of Fingerstick Devices on More than One Person Poses Risk for Tr

＊ Information of CaviWipe disinfectantCaviWipes Disinfecting Towelettes were purchased from METREX RESEARCH CORP, and the EPA Reg. is 46781-8. CaviWip

192.8 Reviewing Results in Memory1) Press the “M” button（main button）to turn on the meter.2) When the test strip symbol flashes, press the “M”

206) At 7 days average result, press the “M” button again, you can read test results in memory, the latest test result will be shown for one m

2121days28daysMemMemMemMemMemDelALLMemDelMem If you want to turn off the meter while you are in the memory and average, you can press the “S” butt

222.9 Viewing Date, Time or Temperature1) Press the “＜” button（Left arrow button）date, time and clock symbol（ ） will be shown on the screen f

23Section 3. Important Notes3.1 Caring for Your MeterTaking care of your meter is very simple. Just follow the guidelines shown below：1) Do not disa

24• All-symbol Message :3.3 Explanation of DisplaysWhen you press the “M” button or insert a test strip into the meter, all symbols willbe displayed

25• Sample Application Message :This requires you to apply the blood sample or control solution to the test strip after inserting a test strip. A

26You can select mmol/L in setting mode. The units will be displayed along with the test result.MemMem• Units of Test Result :3.4 Error Messages &am

27Cause:Damaged meter.Action:Contact your local authorized distributor of Blood Glucose Monitoring System.E-O, E-OO, E-tF, E-SCause:

Blood Glucose Monitoring System2467910111922232324262828Expected Values 1Blood SamplingAlarm settingViewing Date, Time, or TemperatureTesting Control

283.5 Expected ValuesExpected blood glucose levels for people without diabetes:TimeRange (mmol/L)fasting 3.9-6.1less than 7.8 Two hours after meal

Note :

If you pick up this book, please contact above.

2Section 1. Contents & Specifications1.2 Product Specifications & Operating ConditionsStorage ConditionsMemory CapacityMeasurement UnitDispl

3System Operation Conditions :Test Strips Operation ConditionsTemperature：50~104°F(10~40°C)Humidity 20%~80%RH.Using the Blood Glucose Test Strips only

4 Blood Glucose Meter (back) :1.3 About the systemLCD DisplayShow blood glucose test results and messagesLeft Arrow Button /Time d

5How to assess that enough blood has been sampled ? Look at the sampling window on the test strip.If you have enough blood on the strip, you willno

6Section 2. How Your System Works2.1 Installing / Relacing the BatteryYour Blood Glucose Monitoring System is packed with one 3-volt li

72.2 Setting the Year, Date, Time, and Temperature Units＊ Steps to set the Year, Date, Time, and Temperature Units :1) Press the “S” butt